Welcome Visitor, you can login or create account.

Follow Us On
Home > Products > Gyro > KDS Flymentor 3D Gyro
KDS Flymentor 3D Gyro

KDS Flymentor 3D Gyro

Add to Compare
Item details
Weight: 37 grams
Stock: Out of stock

  Share This   Add To Facebook   Add To MySpace

Product Description :  
The functions of Flymentor:

New type of sensing process provides reliable geographical positioning, completely independent of the visible horizon.
Particular CCD sensor can catch the ground picture to compare, and prevent helicopter from drifting.
Adjust the working status of Flymentor by AUX Channel, switchable gain system offers three different positions: Off, stabilisation and Position-holding mode. 
Head lock gyro outside setting and Swashplate mixer.
Control the sensitivity and mode of gyro by GEAR Channel.
Support helicopters with 3S 120��swashplate,or 3S 140��swashplate,or 4S 90��swashplate, or 4S 90��+45��swash plate.
Attitude stabilisation in inverted flight. 
Set Flymentor by computer USB adapter.
If you use FM/PPM radio equipment, Flymentor will make the ailerons, elevator and tail servo back immediately. The pitch will remain in the final signal position. And Flymentor will switch to position mode automatically. The sensitivity is 70%.


KDS Flymentor 3D Flight Altitude Stabilisation and Positioning System

Automatically Hovering in a Fixed Position - KDS Flymentor 3D Stabilizing System
The KDS Flymentor 3D contain 3 components, the Flymentor Mixer, a CCD Camera and a 3-Axis Gyro. The system act as a Auto Pilot, it will only steps in when you don't give any input, but once you move your hands on the control sticks again, the system will de-activate and let you take charge again, pretty amazing, isn't it? Just like a real Auto Pilot when you need a break. The system provides 2 main features, Stabilizing Mode and Positioning Mode.

What is Stabilizing Mode?
Under this mode, there will be solid red and green light on the Flymentor Mixer, the CCD will not be working, only the 3-Axis Gyro is working. When you play the helicopter outdoor, there is wind, right? When wind pass thru the helicopter, it will push the helicopter and making it up side down, you will need to adjust the control sticks constantly to prevent this from happening. By using the Flymentor, it will automatically correct the cyclic servos and keeps the helicopter always in horizontal mode. Thanks to the 3-Axis gyro, it can work all around 360 degree correction.

What is Positioning Mode?
In this mode, there will be solid green light on the Flymentor Mixer, the CCD Camera and the 3-Axis Gyro are both working. The CCD Camera will constantly taking pictures of the ground, and compare each frame, to see if the helicopter is drifting, then it tells the Flymentor Mixer to give correction to all cyclic servos. Resulting the helicopter will stay in a Fixed position. The concept is basically an Eye watching the ground and make adjustment, kinda like a real human. But note that the system is not hooked up with the throttle, the attitude of the helicopter is still in your control.

About the Flymentor Mixer
This mixer is the brain of the whole system, it receives signal from the CCD Camera and the 3-Axis Gyro, then it commands all servos(Cyclic and Rudder Servos) to do the job. It can be placed anywhere, just far from vibration and heat.

About the CCD Camera
Used for "Positioning Mode". The CCD Camera should be mounted underneath the main shaft or on the side frame of the helicopter, with the lens pointing at the ground and free from vibration, it works best in the attitude of 1m to 3m. The CCD Camera's job is to take image of the ground, then to provide a signal to the Flymentor Mixer, and gives the correction to the cyclic servos. To have best result, make sure that there are enough "Light" and "Something" on the ground surface, like grass and gravels, because the Camera can't see very well in dim condition and it can't recognize flat snow or flat sand, it requires "Something" to see, it will not work in dim condition or low contrast color surface.

About the 3-Axis Gyro
Basically, they combine three gyros and place them on X, Y and Z axis, so it sense 3D movements now instead of rudder movement only. This gyro also contain some Temperature sensor and some other sensors too. Also, needs to isolate it from vibrate and heat.

How to install the KDS Flymentor 3D Stabilizing System?
Connect the Flymentor Mixer to the Receiver as first picture, then turn on the transmitter and choose "Swashplate Type" to 1-Servo, meaning you don't use the CCPM from your transmitter no more, you will be using the Flymentor Mixer to do the CCPM mixing, then switch off transmitter. Then connect Servos to Flymentor Mixer as second picture, and mount the CCD Camera as third picture and mount the Gyro as usual on to the helicopter, just make sure it is placed horizontally. After installing the hardware, then you install the software into the computer and use the USB cable to connect Flymentor Mixer to the computer to do the setup. From now on, all the Sub-Trims, Channel Reverse, Servo Travels.... almost everything needs be set up using the software, don't adjust the value on the transmitter anymore, except Gyro Sensitivity, it can still be adjusted thru the transmitter.

Specifications :
- Voltage: 4.8V - 6.0V
- Current: 55mA (under 5V)
- Temperature Range: 0℃ - 40℃
- Weight: 37g
- Support helicopters with 3S-120o swashplate, or 3S-140o swashplate, or 4S-90o swashplate, or 4S-90o + 45o swash plate

Copyright © 2013 RC HOPEZ   |   e-commerce by webShaper™  
Terms   |   Return & Refund Policy   |   Great Deals via RSS Feed